broaching
推荐文章
n.
拉削；推削；铰孔；扩孔
v.
谈起( broach的现在分词 )；打开并开始用；用凿子扩大（或修光）；（在桶上）钻孔取液体
英英释义
broach[ 'bəutʃiŋ ]
n.a decorative pin worn by women
同义词：broochbreastpin
v.bring up a topic for discussion
同义词：initiate
词组短语
broaching machine拉床；剥孔机，铰孔机
双语例句
用作名词(n.)
A new simple method for broaching spline holes with a common machine, which has enlarged Screwpitch, is introduced.
介绍了一种在有增大螺距的普通车床上拉削花键孔的新方法。
权威例句
Cemented carbide broach and broaching machineDevelopment of an online machining process monitoring system: a case study of the broaching process
Dynamic Instability in Quartering Seas; The Behaviour of a Ship During Broaching
Tool condition monitoring in broaching
Broaching the Subjects of Race, Ethnicity, and Culture During the Counseling Process
URANS analysis of a broaching event in irregular quartering seas
Nonlinear dynamics of ship capsizing due to broaching in following and quartering seas
Broaching tool for producing multi-edge boreholes i.e. hexagonal profile boreholes, in work piece, has broaches whose axial rear end...
Machining of Hard Materials
The Nonlinear Dynamics of Ship Motions: A Field Overview and Some Recent Developments
1. The topic to keep in mind is' broaching '.
专题要记住是'拉'。
youdao
2. Broaching the subject of death with a loved one.
向深爱的人提出死亡的话题。
youdao
3. But how long do I wait before broaching the subject?
但是我还得等多久才能跟她提啊？ ！
youdao
4. When broaching the topic of smoking, always use a positive tone.
谈论关于吸烟的话题时，请记得使用正面的表达方式。
youdao
5. A destabilization mechanism behind the broaching-to is discussed.
本文还讨论了横甩后的不稳定机理。
youdao
6. They managed to keep the boat from broaching to in the heavy seas.
他们设法使船在波涛汹涌的海面上不突然横转。
youdao
7. Which has been calculated broaching, and must be less than the actual pull broaching machine.
其中计算所得到的拉削力，必须小于拉床的实际拉力。
youdao
8. Suitable for all machining operations, even the most difficult and demanding broaching machining.
适用于所有加工方式，就算是最困难和最苛刻的拉削操作。
youdao
9. After being positioned and locked by the worktable, the work-piece will enter the broaching state.
经过工作台定位、锁紧，工件进入拉削状态。
youdao
10. L Suitable for all machining operations, even the most difficult and demanding broaching machining.
适用于所有加工方式，就算是最困难和最苛刻的拉削操作。
youdao
11. In this article the broaching internal round hole system is simplified to the single-freedom system.
本文首先将内孔拉削系统简化为单自由度系统，给出其振动的数学模型并对其进行运算和处理。
youdao
12. A simple jig and Fixture used in American small machine repair shops for broaching operation on various lathes.
介绍了一种美国小型机械修配厂在各种车床上进行拉削加工用的简易工装。
youdao
13. It will be widely use to broaching the high quality PCB board and other accurate mechanical broaching, and so on.
种高质量pcb的钻孔和各种机械部件的精确钻孔等其它精确钻孔的应用。
youdao
14. A new simple method for broaching spline holes with a common machine, which has enlarged Screwpitch, is introduced.
介绍了一种在有增大螺距的普通车床上拉削花键孔的新方法。
youdao
15. Improvement is made to the positioning feller gauge in flywheel keyway broaching machine by V-type auto center align.
利用V型块自动对中定位原理，对飞轮键槽拉床定位塞尺进行改进。
youdao
16. After turning, milling, and broaching and other machining method of processing, then through the whole heat treatment.
经过车削，铣削，和拉削等机加工方法加工而成，再经过整体热处理。
youdao
17. After broaching, the work-piece will enter the charging and discharge state again, and this machine has completed one cycle.
拉削完成后，工件又进入上、下料状态，机床完成一个循环价段。
youdao
18. These machines are designed for broaching holes of various geometrical forms in mass and batch production with high efficiency.
本系列机床用于拉削各种几何形状的孔，生产效率高，适于大量生产和成批生产。
youdao
19. Finally, it is considered what specific measures should be taken to improve the surface integrity of titanium alloy in broaching.
分析了为提高钛合金拉削的表面完整性所应采取的措施。
youdao
20. Miss glover suffered terribly from nervousness, and the notion of broaching so delicate a subject caused her indescribable tortures.
格洛弗小姐由于神经紧张而极度痛苦，那种认为要对非常棘手的问题担风险的想法使她感到有说不出的苦恼。
youdao
21. The weak links of the bed are found by the analysis and a proposal for improving the structural design of broaching machines was presented.
从计算结果分析了该机床支承件薄弱环节，并对卧式拉床结构提出了设计改进的建议。
youdao
22. The structure principle, designing and manufacturing key points of the turning - broaching cutter for machining crankshafts are introduced.
介绍了加工曲轴用车拉刀的结构原理和设计、加工要点。
youdao
23. During the turning and broaching operation of titanium alloys, experiments and researches of cutting temperatures are of great significance.
在钛合金车削和拉削加工过程中，对切削温度进行试验研究有着十分重要的意义。
youdao
24. During the turning and broaching operation of titanium alloys, experiments and researches of cutting temperatures are of great significance.
在钛合金车削和拉削加工过程中，对切削温度进行试验研究有着十分重要的意义。
youdao
broaching
