ejector pin
释义
出坯杆；起模杆；推出机杆；推顶杆
权威例句
Ejector pinEjector pin
EJECTOR PIN
Ejector unit of injection molding machine and method of detecting protrusion start position of ejector pin
Layout and sizing of ejector pins for injection mould desian using the wavelet transform
Ejector pin and breechblock assembly for firearms
Mold for use in a gas-assisted injection molding system and ejector pin subsystem including a split pin for use therein
Decelerated ejector pin system and method for operating the same
Properties and optimization of coated sand used for oil pump and ejector pin core of the 4DA1 engine block
Design of Thin Slanted Ejector Pin Demoulding of the Mould for Cell Phone
Advertising workshop project of Krungsri in-hand banking
Enhancement of weld line mechanical strength using a novel ejector‐pins compression system
The Research of a Steel (TG 2) Used for Ejector Pins of Plastic Dies
1. The undercut area may stick slide. We may consider to add an ejector pin on the slide.
产品扣位处可能粘行位。我们需考虑行位上加顶针；
youdao
2. Each ejector pin diameter has a number of different lengths associated with it.
每一种顶杆直径有许多不同长度。
youdao
3. The location of the ejector pin elements, and the number used, is dependent on the components size and shape.
顶杆零件的位置和数目，取决于塑件的尺寸和形状。
youdao
4. The plain diameter ejector pin may be used in one of two ways.
普通的顶杆可以有两种使用方法。
youdao
5. The ejection mechanism used pin ejector to pull the plastic parts out with move slanting slide simultaneously leaving circular arc concave position.
脱模机构采用推杆推出塑件的同时带动斜滑块脱出圆弧形凹位，使脱模机构简单实用。
youdao
6. The product has excellent tooling quality and machining performance, so as to alleviate and avoid the deformation of ejector pin because of heat treatment.
该产品具有良好易切削性能和机械加工性能，从而避免了薄壁推管(司筒)因热处理而产生变形。
youdao
7. Clearance of ejector pin is used to vent little quantity air or the part may intervene with vent plug and ejector pin.
推杆间隙排气用于排气量不大或者开设排气塞会与推出机构产生干涉的部位。
youdao
8. The structure, operating principle and action of mechanism of automatic sprue cutting by ejector pin in thermosetting plastics injection mould was described.
介绍了推杆自动切断浇口机构在热固性塑料注射模中的具体结构、 模具工作过程。
youdao
9. Introduced a inner ejection pin in Angle ejector structure that prevent product pulling pulling injury and displacement.
介绍了一种从斜顶内顶杆顶出，防止产品拉伤、位移的基本结构。
youdao
10. Suitable sizes of push-back pins may be selected from a standard ejector pin range.
回程杆的合适尺寸可以在标准的顶杆范围内选择。
youdao
11. The direction of movement of this ejector pin is, therefore, controlled by this hole.
因此顶杆的运动方向由这个孔来控制。
youdao
12. At present, the phenomenon of axial desquamation for an individual ejector pin plate or an annular cutter can occurs in a disposable digestive tract anastomat component.
目前，一次性使用的消化道吻合器组件，会发生个别推钉片或环形切刀轴向脱落的现象。
youdao
13. Our main products are pin header connector, female header connector, box header connector, ejector header, round needles, IC sockets with round holes, flat cables and other types of connector.
主要产品有排针、排母，简牛、牛角，圆针、圆孔ic插座，排线以及其它各类连接器。
youdao
14. The forming technology of the cell phone piece was analyzed. The structure of the mould was redesigned to improve the strength of the thin slanted ejector pin.
分析了手机盖零件的成型工艺性能，改进了模具的结构设计，解决了传统设计方法中存在的细小斜推杆强度太差问题。
youdao
15. The vent system composed of vent groove, vent plug and clearance of ejector pin can fit the need of venting.
采用分型面排气槽、顶杆间隙排气与排气塞排气相结合的排气系统设计能够很好地满足模具排气需要。
youdao
16. Hydraulic drawing-core mechanism was adopted for two-side of inner-sinking in the die casting die, and pre-resetting mechanism was set to avoid the interference of core slide with ejector pin.
压铸件内凹处两侧采用液压抽芯机构抽芯，为防止滑块型芯与推杆发生干涉而设置了预复位机构；
youdao
17. Hydraulic drawing-core mechanism was adopted for two-side of inner-sinking in the die casting die, and pre-resetting mechanism was set to avoid the interference of core slide with ejector pin.
压铸件内凹处两侧采用液压抽芯机构抽芯，为防止滑块型芯与推杆发生干涉而设置了预复位机构；
youdao
18. ejector plate return pin
排出频回杆
-- 来源 -- 英汉 - 翻译参考[网络]
19. ejector pin mark
脱模顶销痕
-- 来源 -- 英汉 - 翻译参考[网络]
20. ejector guide pin
顶出导梢
-- 来源 -- 英汉 - 翻译样例 - 产品
21. ejector pin plate
脱模顶销持板
-- 来源 -- 英汉 - 翻译参考[网络]
22. ejector pin
顶脱销
-- 来源 -- 英汉 - 翻译样例 - 工程
23. flat ejector pin
扁推杆
-- 来源 -- 英汉 - 翻译参考[网络]
24. Ejector Sleeve Pin
套筒
-- 来源 -- 英汉 - 翻译样例 - 产品
25. ejector pin with cylindrical head
圆柱头推杆
-- 来源 -- 英汉 - 翻译参考[网络]
26. injection mold is determined, as well as the design of feed system, slide side-drawing mechanism, slanting pin
通过对机箱面板结构及特点的分析,确定了其注射模具的总体结构设计方案,并对浇注系统、块侧抽机构、销机构、出系统以及镶块结构的设计进行了详细论述。
-- 来源 -- dict.cnki.net
ejector pin
