overfill
v.
把…装得溢出；
变形
过去式：overfilled过去分词：overfilled现在分词：overfilling第三人称单数：overfills
英英释义
overfill[ ,əuvə'fil ]
v.fill beyond capacity
"overfill the baskets"
双语例句
用作动词(v.)
Do not overfill as boiling water may be ejected.
在烧水时请不要将水加得过满，因为这样可能会使水溢出。
It is hazardous to overfill liquid storage tanks; level in the tank must be monitored.
贮罐过量充装液体是危险的,液位必须被监控。
权威例句
Overfilloverfill
Overfill or ultrafiltration? We need to be clear.
Pregnancy: an overfill or underfill state
Anatomy of an overfill: a reflection on the process
Overfill of Peritoneal Dialysis Bags as a Cause of Underestimation of Ultrafiltration Failure
A critique of the overfill hypothesis of sodium and water retention in the nephrotic syndrome.
Cationic Surfactants for the Control of Overfill Bumps in Cu Superfilling
Age and backfill/overfill stratigraphy of two tufa dams, Tigray Highlands, Ethiopia: Evidence for Late Pleistocene and Holocene wet ...
Electrodeposition of Cu in the PEI-PEG-Cl-SPS additive system reduction of overfill bump formation during superfilling
1. It is advised to overfill the bucket to allow for settling.
建议装满桶，也允许石头溢出桶。
youdao
2. They provide a portable, flexible solution to varying overfill requirements for safe top loading.
针对安全顶部灌装的各种防过量灌装要求，杆式探头提供了一种便携、灵活的解决方案。
youdao
3. Cane probes are used to provide overfill detection where a permanent sensor cannot be properly affixed to a tank or rail car.
在永久性溢出探头无法适当固定在储罐或铁路槽车上的情况下，可用杆式探头来进行过量灌装的检测。
youdao
4. The overfill quantity is calculated according to actual left quantity in Automatic Import License and within the stipulated upper limit.
最后一批货物进口时，其溢装数量按该自动进口许可证实际剩余数量并在规定的允许溢装上限内计算。
youdao
5. For high and low alarms, overfill protection, pump control, including wide pressure and temperature requirements, and hygienic applications.
对于高，低报警，溢流保护，泵控制，包括宽的压力和温度的要求，和卫生应用。
youdao
6. That is, one or more partitions must be nearly full or you must expect to add enough data to overfill a partition in the near future before you consider resizing.
这就是说，您考虑调整分区的前提是，一个或多个分区必须是快满了，或者说您确定不久将会添加很多数据，可能会导致溢出。
youdao
7. A piece of hot metal sufficient to slightly overfill the die shape is placed in the bottom die, and the top die is forced against it, so that the metal takes the internal shape of the die.
将一块大小足以充填模腔并能稍有溢出的加热金属放入底模，并将顶模加压合拢，这块金属便获得该模腔的形状。
youdao
8. A piece of hot metal sufficient to slightly overfill the die shape is placed in the bottom die, and the top die is forced against it, so that the metal takes the internal shape of the die.
将一块大小足以充填模腔并能稍有溢出的加热金属放入底模，并将顶模加压合拢，这块金属便获得该模腔的形状。
youdao
overfill
