locknut
n.
防松螺母，对开螺母；
英英释义
locknut[ 'lɔknʌt ]
n.supplementary nut that is screwed down on a primary nut to prevent it from loosening
同义词：safety nut
权威例句
Lock nutLock nut
LOCKNUT
Locknut assembly
Square locknut
HUB LOCKNUT SOCKET TOOL
Locknut with locking coil and coil support
Insulated grounding hub locknut unit
Research on a new-type intelligent locknut
High‐pressure low‐temperature locknut cell for both EPR and NMR studies to 10 kilobars and 77 K
The Expression of Anti-loosing Friction Moment of Fe-based SMA Locknut
The Research on the Torque Design and Calculation Method of Locknut on Turbochager Compressor Impeller
Optimization on the Performance of a Precision Flank-Locking Locknut Considering the Machining and Operational Parameters
1. For example jersey cloth, rayon locknut and nylon tricot are made in this method.
例如紧身运动套衫面料、粘胶长丝经平绒针织物和尼龙经编织物都是用这种方法制成的。
www.youdict.com
2. Now, add a locknut groove on the right edge of the section to the selected shaft section.
现在，将剖面右侧边上的防松螺帽槽加入至选取的轴剖面中。
danci.911cha.com
3. If valve clearance needs to be adjusted, loosen the locknut on rocker arm adjusting screw. Turn adjusting screw until feeler gauge slips with a slight drag.
如果气门间隙需要调节，松开摇臂调节螺丝上的防松螺母，转动调节螺丝直到测隙规滑动时稍带阻力为止。
http://www.chazidian.com
4. Change of one section of Kelly bar should get suggestions of manufacturer; part 2 is locknut, normal nut should not be changed for it.
更换其中一节钻杆要征求钻杆生产厂家建议；件2为防松螺母，不要换为普通螺母。
danci.911cha.com
5. Recheck clearance on all valves again after locknut is tightened.
防松螺母拧紧后，再对所有气门的间隙重新检查一次。
www.dictall.com
6. A sealed collet having improved radial flexibility is provided for facilitating removal from a locknut of a chuck assembly.
本发明提供了一种具有改进的径向挠性的密封套爪以有利于从卡盘组件的防松螺母上卸除。
danci.911cha.com
7. The valve is mainly made up of handle, body, disc, locknut and seal etc.
手动密闭闸阀主要由把手、阀体、插板、锁紧螺钉、密封装置等部件组成。
danci.911cha.com
8. To replace seat/ stem module shut off supply, loosen locknut and back off adjusting screw.
要更换阀座/杆模块，先关闭供应管道，松开锁紧螺母，退出调节螺丝。
www.dictall.com
9. Position locknut over top of fuel pump module.
将锁定螺帽放在燃油泵模组上。
www.dictall.com
10. And 6 intake valves. Tighten valve adjusting screw locknut to 27 N·m (20 lb-ft).
将气门调节螺丝防松螺母拧紧至27牛顿·米（20磅-呎）。
danci.911cha.com
11. The locknut is rotated to lock the spring chuck, so as to clamp a drill bit which is enabled to rotate along with the spindle to carry out the drilling processing.
通过转动锁紧螺母锁紧弹簧夹头从而夹紧钻头，使钻 头跟随主轴旋转进行钻削加工。
ip.com
12. The locknut torque needed to move the washer at the maximum washer interference fit shall not exceed the torques given in Table 3.
锁紧螺母扭矩压紧垫片时，其与垫片的最大相互作用力不能超过表3所给扭矩值。
www.jxcad.com.cn
13. The locknut torque needed to move the washer at the maximum washer interference fit shall not exceed the torques given in Table 3.
锁紧螺母扭矩压紧垫片时，其与垫片的最大相互作用力不能超过表3所给扭矩值。
www.jxcad.com.cn
14. Fuel Pump Module Locknut
燃油泵模组锁定螺帽
-- 来源 -- 英汉 - 翻译参考
15. Adjustment Cap Locknut
调节帽防松螺母
-- 来源 -- 英汉 - 翻译参考
16. Adjustment Screw Locknut
调节螺钉防松螺母
-- 来源 -- 英汉 - 翻译参考
17. Position locknut over top of fuel pump module.
将锁定螺帽放在燃油泵模组上。
-- 来源 -- 英汉 - 翻译参考
18. Tighten locknut 1 to fix the thread stand.
拧紧固定螺母1不让线架装置松动。
-- 来源 -- 英汉 - 翻译参考[网络]
19. For example jersey cloth, rayon locknut and nylon tricot are made in this method. Sometimes these materials are tubular to make cutting out more economical.
例如紧身运动套衫面料、粘胶长丝经平绒针织物和尼龙经编织物都是用这种方法制成的。有时这些面料是圆筒的,裁剪时更经济,这就是针织法。
-- 来源 -- 英汉 - 翻译样例 - 行业
20. Flared type tube fittings--Locknut
GB/T5649-1985扩口式管接头锁紧螺母
-- 来源 -- 英汉 - 翻译参考[网络]
21. galvanized locknut
镀锌锁母
-- 来源 -- 英汉 - 翻译参考[网络]
22. To replace seat/ stem module shut off supply, loosen locknut and back off adjusting screw.
要更换阀座/杆模块，先关闭供应管道，松开锁紧螺母，退出调节螺丝。
-- 来源 -- h6688.com
23. The fuel tank assembly consists of: the fuel tank, fuel pump module assembly, fuel pump module locknut/gasket, and rollover valve (refer to Group 25, Emission Control System for rollover valve information).
油箱组合包含：油箱，油泵模组组件，油泵模组锁定螺帽／垫圈，和逆止阀(请参阅单元25“排放控制系统”来获取逆止阀资讯)。
-- 来源 -- 英汉 - 翻译参考
locknut
