warpage
n.
翘曲，扭曲，热变形；
双语例句
用作名词(n.)
The resulting benefits are high stiffness and load bearing at low weights and with low warpage.
最终带给产品的好处是在低重量和低翘曲情况下体现出的高刚性和承载能力。
To understand the mechanics of wafer warpage, research is performed on the effect of the lift-off procedure and material thickness on wafer warpage.
本研究进一步为了解晶圆翘曲的力学特性，研究雷射剥离过程及材料厚度，对氮化镓发光二极体晶圆翘曲之影响。
权威例句
WARPAGE-REDUCING PACKAGING DESIGNWarpage optimization of a bus ceiling lamp base using neural network model and genetic algorithm
Topographic changes in contact lens-induced corneal warpage.
Optimal process conditions of shrinkage and warpage of thin‐wall parts
Efficient warpage optimization of thin shell plastic parts using response surface methodology and genetic algorithm
Minimization of warpage and sink index in injection-molded thermoplastic parts using Taguchi optimization method
Comparison of the warpage optimization in the plastic injection molding using ANOVA, neural network model and genetic algorithm
The use of Taguchi method in the design of plastic injection mould for reducing warpage
Tool, method for drying recording sheet using the same, method for correcting warpage using the same, and unit having the same
Determination of effecting dimensional parameters on warpage of thin shell plastic parts using integrated response surface method an...
1. The flanging process at high temperature can improve effectively formability, get rid of peripheral warpage and elliptical opening, but the lip surface and wall thickness can not be evened yet.
高温热翻边成形有效地提高了成形极限，并消除了凸缘平面翘曲和口部椭圆化，但口部高差以及壁厚不均等现象依然存在。
dict.cnki.net
2. The principle of precompensation for deformation was presented, which was applied to the shaping of an automobile fan and effectively helped lower the shrinkage deformation and warpage of the product.
介绍了变形预补偿的原理，以汽车风扇为例，成功地降低了汽车风扇的收缩变形和翘曲变形，为解决制品变形问题提供了一条新的思路。
www.dictall.com
3. All calculations confirm that a compound thickness ratio of 1.2 results in minimal warpage for a large chip TSOP.
所有的计算结果证明化合物厚度比为1.2，会使大芯片TSOP的翘曲问题最小化。
dict.cnki.net
4. An optimized ram speed profile fully uses the friction heat to keep the best flow characteristics, which corrects many of the fill and warpage problems.
最适化螺杆速度充分运用摩擦热，将塑流保持在最佳状态。许多充填和翘曲的问题也就迎刃而解。
www.wxzyou.com
5. Base on the nonlinear large analysis, warpage of matrix SDBGA during the whole assembly processes are predicted.
文中基于非线性特性分析、预测了在整个集成工艺中SDBGA阵列的翘曲。
dict.cnki.net
6. It has improved impact resistance and low warpage.
它改善了耐冲击性和低翘曲。
dict.cn
7. The troubles, including hesitation, short shot, sink mark, blush, jetting, warpage and long cooling time etc.
这些麻烦包括了迟滞现象、短射、凹陷、发赤、喷流、翘曲及长冷却时间等；
www.wxzyou.com
8. The results indicate that viscoelastic-GK calculation with relaxation of shear modulus and of bulk modulus using the multilayer shell element is the most appropriate method for predicting the warpage.
研究结果表明预测翘曲问题最合适的方法是使用多层壳体元缩减切变模量和体积模量，计算出粘弹性GK。
dict.cnki.net
9. This paper investigates application of residual stresses and warpage simulation on the prediction of injection-molded transparencys optical distortion.
研究了注射成型翘曲应力计算模拟对成型透明件光学畸变预测的意义。
www.dictall.com
10. Basically smooth and shiny on the surface, have no obvious fault of contraction dent, brindle, warpage, defective bubble and plastify.
表面基本上平滑光亮，无明显收缩凹痕，斑纹，翘曲，气泡及塑化不良等缺陷。
www.qy6.com
11. Execute reliability tests. E. g. SEM/EDX, small press machine, TST, hot oil test, CAF, climate test, warpage measurement, reflow test and so on.
执行特殊要求的可靠性测试，例如SEM/EDX，小型压机，热冲击测试，热油测试，CAF，环境测试，翘曲测量，回流焊测试等。
www.huibo.com
12. If this causes a warpage problem, it sometimes helps to raise the overall water temperature and slow the rate of heat transfer.
如果这样还有翘曲问题，那么升高总的水温并降低热交换速度是有益的。
www.plas2006.com
13. In this paper, warpage of composite shell segment with arbitrary layup during the curing process is studied.
为此本文研究了任意铺层复合材料开口圆柱壳的热翘曲变形。
dict.cnki.net
14. The speckle projection correlation technique is used to measure the chip warpage.
本文采用投影散斑相关法对芯片翘曲度进行了测量。
dict.cnki.net
15. With comparison to the experimental measurement results, it is found that the linear method is not able to capture the warpage behavior while nonlinear large deformation simulation can.
与实验测量结果相比，线性方法不能反映翘曲形态而非线性大变形仿真能够反映出这种翘曲。
dict.cnki.net
16. This paper introduces the experimental studies on the warpage of injection molded strip parts in the design of part structure and mold gate and the selecting of molding conditions and materials.
从制品结构和模具浇口设计、原材料和成型条件的优选诸方面对长条形注塑件翘曲变形进行了系统的试验研究。
www.chemyq.com
17. Taking the forming of computer case panel as an example, the process of the filling, cooling and warpage of the plastics parts in the injection molding were simulated by means of MPI software.
以电脑机箱面板为实例，使用MPI软件对塑料件注射过程中的填充、冷却、翘曲情况进行模拟。
www.chemyq.com
18. Series of glass fiber reinforced PET with low warpage have been prepared according to the mechanism and different methods of reduction of warpage.
依据降低翘曲的机理，选用不同降低翘曲的方法，制备了系列低翘曲玻纤增强PET复合材料。
www.dictall.com
19. According to the statistical results, the injection time is the most important affecting factor on warpage.
结果表明，注射时间对注塑件翘曲变形的影响最大。
lib.cqvip.com
20. The cause and rule of warpage in the injection-moulding products was introduced. It listed the guarding measures in mold structure, molding technology and forced patterns against warpage.
介绍了注塑制品翘曲变形的原因及其规律。从模具结构、成型工艺、强制定型等方面，列下了避免翘曲变形的措施。
dict.cnki.net
21. The experimental and simulation results of bi-laminates during non-pressed post mold cure revealed that PMC could reduce the warpage.
未加压的后熟化实验与模拟结果显示：后熟化制程可减低翘曲量。
danci.911cha.com
22. A numerical study of residual stresses and warpage was undertaken according to the characteristics of plastic injection molding process.
针对塑料注射成型工艺的特点，提出了残余应力和翘曲变形的数值模拟方法。
wiki.gy65.com
23. An even cooling design becomes very important to control the shrinkage and warpage at an acceptable level.
为了将收缩弯翘控制在可以接受的程度，均衡的冷却设计变得非常重要。
vip.handlers.cn
24. For example, post-mold warpage may render parts unusable because of dimensional changes that are not completed for weeks or months after molding.
例如，成型后的翘曲会导致零件不能用，因为在成型后几星期甚至几个月尺寸变化都不能完成。
www.mapeng.net
25. For example, post-mold warpage may render parts unusable because of dimensional changes that are not completed for weeks or months after molding.
例如，成型后的翘曲会导致零件不能用，因为在成型后几星期甚至几个月尺寸变化都不能完成。
www.mapeng.net
26. glost warpage
翘曲, 弯曲;畸变(釉烧中产生的变形)
-- 来源 -- 英汉 - 短句参考
27. warpage test
翘曲试验
-- 来源 -- 英汉 - 翻译样例 - 产品
28. Sim? ilarly, an increase in case depth, particularly uneven case depth in case hardening steels, increases warpage on quenching.
与此类似，渗碳层厚度越大，特别是对于渗碳层厚度不一的渗碳用钢，淬火时更易产生翘曲。
-- 来源 -- www.credit5.cn
29. The material is of practical use in case of dampness, has good mechanical properties, overcomes defects such as warpage and deformation that has Sorel cement peculiarly.
该材料适用于潮湿条件下,具有良好的力学性能;同时克服了镁质胶凝材料所特有的易翘曲、形的缺点。
-- 来源 -- dict.cnki.net
30. Uneven hardening, with the formation of soft spots, increases warpage.
淬火不均部件上将出现软点，增加翘曲可能性。
-- 来源 -- www.credit5.cn
31. testing methods for warpage of refractory bricks
耐火砖翘曲测定方法
-- 来源 -- 英汉 - 翻译参考[网络]
32. Under certain conditions, the calculating formula of interlayer stress and the stress-distributing diagram in cut planes are provided, and the mathematical model for warpage deformation calculation is also established.
建立了翘曲变形的数学模型，讨论了各种工艺参数（层数、扫描线长、成型室温度、层厚等）对翘曲变形量的影响。
-- 来源 -- 网友提供
warpage
