adhesive failure
释义
密着破坏，脱胶（橡胶）；
双语例句
Experiment results also reveal that stiffened thin-walled composite plate can bear greater load after buckling.And buckling mode change after stringer adhesive fails.
试验还发现复合材料薄壁加筋板结构有较高的后屈曲承载能力，后屈曲过程中由于桁条脱胶会造成屈曲模态的变化。
权威例句
adhesive failureMechanics of Adhesive Failure. II
On the apparent relation between adhesive failure and melt fracture
Failure at the dental adhesive-etched enamel interface.
Failure at the dental adhesive—etched enamel interface
Bonding and Failure Mechanisms in Aluminium Alloy Adhesive Joints
The role of the interphase in the environmental failure of adhesive joints
Environmental Failure of Structural Adhesive Joints
Prediction of deformation and failure of rubber-toughened adhesive joints
Adhesive Failure and Deformation Behaviour of Polymers
1. The reason of the failure of epoxy bonded joint in water was that the epoxy adhesive on the metal surface was substituted for water.
环氧胶接接头在水中破坏失效的原因主要是渗入到胶接层的水分子取代了胶粘剂分子在金属表面的粘附。
youdao
2. Through pullout tests for shear resistance of the adhesive steel bar in the metal tube, the bond principals and failure modes of adhesives are studied.
通过对钢筋与金属套筒之间采用植筋胶粘结的拉伸抗剪试验，探讨了植筋胶的粘结机理和拉伸抗剪破坏模式。
youdao
3. Bat a decisive factors of ring failure are the adhesive wear and fatigue wear.
而钢领失效的决定性因素是粘着磨损和疲劳磨损。
youdao
4. The failure form of joint, mechanical analysis of joint, joint design and test methods of adhesive bonding of composites are presented briefly in this paper.
本文简略叙述复合材料胶接的接头破坏形式，接头力学分析，接头设计及测试方法。
youdao
5. Debonding at CFRP plate and adhesive interface is a common failure mode for NSM CFRP plate to concrete.
板-胶剥离破坏是混凝土表层嵌贴CF R P板条加固方式常见的破坏形式。
youdao
6. Attention should be paid to the shear strength of the adhesives since the shear stress could cause failure in the adhesive layer.
粘接剂主要以剪切的方式破坏，粘接剂剪切强度是一个值得注意的问题。
youdao
7. Bonding force of substrate and adhesive layer is large. No adhesive failure occurs during storage and construction.
基材与胶层结合力大，在存放或施工过程中不存在脱胶现象。
youdao
8. Through the control of critical points as the FRP length, number of FRP layer and mechanical property of adhesive, which is useful for restraining debonding failure.
通过对纤维布粘贴层数、长度以及粘结胶力学特性等关键要素的控制，可以有效地抑制粘结剥离破坏的发生。
youdao
9. The test may compare the fractured surface produced to failure analysis results within the adhesive interphase region.
试验比较粘合剂相间区内的断裂面产生失效分析结果。
youdao
10. The failure mechanism of journal bearing of roller cone bit is analyzed, the failure type is adhesive wear, and main factors affecting the adhesive wear are analyzed.
分析了牙轮钻头滑动轴承失效的机理，论证了牙轮钻头滑动轴承失效形式主要为粘着磨损，分析了影响轴承粘着磨损失效的主要因素。
youdao
11. The bond failure rate and the adhesive remnant index were calculated.
计算托槽脱落率和粘接材料残留指数。
youdao
12. The fracture modes observed by using multiplication microscope indicated that the adhesive failure was the most mode of fracture.
断裂方式观察结果显示绝大部分样本的断裂方式都是粘结面型断裂。
youdao
13. The fracture modes observed by using multiplication microscope indicated that the adhesive failure was the most mode of fracture.
断裂方式观察结果显示绝大部分样本的断裂方式都是粘结面型断裂。
youdao
adhesive failure
