camshaft
n.
凸轮轴；
变形
复数：camshafts
英英释义
camshaft[ 'kæmʃɑ:ft ]
n.has cams attached to it
双语例句
用作名词(n.)
This is called an overhead camshaft arrangement.
这被叫为顶置凸轮轴装置。
The eccentric may be part of the camshaft itself or may bolt to it.
偏心轮可能与凸轮轴是一体的，也可能是通过螺钉连接的。
权威例句
Concentric camshaft with varying wall geometry and method of assemblyVariable camshaft timing for internal combustion engine
Saturnian magnetospheric dynamics: Elucidation of a camshaft model
Calculating of the Camshaft Load Torque and Research on Virtual Check Valve Control Strategy
Internal combustion engine of motor vehicle, has intake camshaft and exhaust camshaft that are adjusted such that opening of intake ...
Adjusting device for internal combustion engine, has rotor, which is firmly connected with camshaft, where stator is coupled with dr...
Induction Quenching For Camshaft With Eccentric Wheel
Camshaft advancer for improving efficiency of combustion engine - uses slip-ring-free electric motor to alter position of camshaft r...
Actuator for e.g. diesel engine, has displacement sensor and rotational speed sensor directly/ indirectly attached at outer side of ...
Inventive progress measured by multi-stage patent citation analysis
1. Other possible reasons include problems with the oil pump, rod and main bearing clearances, camshaft stopping playing, or cam bearings and lifters.
其他可能的原因包括油泵问题、杆和主轴承的空隙、凸轮轴停止工作、或者凸轮的方位和升降。
youdao
2. Install cover for camshaft housing.
安装凸轮轴室盖。
youdao
3. The camshaft has a cam, on which there is a lob, or bump.
凸轮轴上有一个凸轮，凸轮上有一个凸角。
youdao
4. In its initial stage the change-of the camshaft is performed.
在他的初始阶段凸轮轴的转换被执行。
youdao
5. Camshaft is one of the important parts on the automobile engine.
凸轮轴是汽车发动机的重要零件。
youdao
6. The eccentric may be part of the camshaft itself or may bolt to it.
偏心轮可能与凸轮轴是一体的，也可能是通过螺钉连接的。
youdao
7. Since 1958, an engine with a single overhead camshaft has been used.
从1958年起，便已使用带有单顶置凸轮机的发动机。
youdao
8. The isothermal quenching process of the ductile iron camshaft was analyzed.
对球铁凸轮轴的等温淬火工艺进行了分析。
youdao
9. Camshaft from the crankshaft through the timing belt or gear or chain drive.
凸轮轴由曲轴通过齿形带或齿轮或链条驱动。
youdao
10. The value-opening mechanism includes a valve lifter and a CAM on a camshaft.
一套气门开启机构包括一个气门挺杆和一个在凸轮轴上的凸轮。
youdao
11. The value-opening mechanism includes a valve lifter and a cam on a camshaft .
一套气门开启机构包括一个气门挺杆和一个在凸轮轴上的凸轮。
youdao
12. The camshaft also fits inside the block, except on overhead-cam engines (OHC).
除了顶置凸轮（OHC）发动机以外，凸轮轴都安装在气缸体里面。
youdao
13. Therefore, the camshaft must revolve at exactly half the speed of the crankshaft.
因此，凸轮轴必须以曲轴正好一半的速度旋转。
youdao
14. It's connecting methods are the key technology in assembling camshaft production.
而其连接方法是装配式凸轮轴制造的关键技术。
youdao
15. Remove the camshaft retaining bolt and remove the sprockets and chain as an assembly.
拆去凸轮轴固定螺栓，并拆去作为一个总成的链轮和链条。
youdao
16. Since the engine has no valves, it doesn't need any camshaft, valve lifters and so on.
因为发动机没有阀门，它不需要任何凸轮轴、起阀器等。
youdao
17. Rocker arm, Rocker arm shaft, Rocker assembly, Valve guide tube, Camshaft bearing Cap.
气门摇臂，摇臂轴，摇臂总成，气门导管，凸轮轴盖。
youdao
18. When you increase the RPM, however, this configuration for the camshaft does not work well.
当您增加转速时，但这种配置的凸轮轴不工作。
youdao
19. The key technology of hollow assembled camshaft is joint between the shaft and the cam lobes.
中空装配式凸轮轴的技术关键为凸轮和轴体之间的连接。
youdao
20. The mechanical fuel pump is used on many vehicles with carburetors and driven by the camshaft.
机械驱动燃油泵用于许多化油器式车辆，它由凸轮轴驱动。
youdao
21. Applied to ductile iron crankshaft, camshaft and other parts of the grinding and other grinding.
适用于球墨铸铁曲轴，凸轮轴等工件的磨削及其它磨削。
youdao
22. The metal shaft, called the camshaft, typically has individual cams for each valve in the engine.
那金属轴叫凸轮轴，翣在发动机里的每个气门一般有各自的凸轮。
youdao
23. The metal shaft, called the camshaft, typically has individual cams for each valve in the engine.
那金属轴叫凸轮轴，在发动机里的每个气门一般有各自的凸轮。
youdao
24. One centrally located camshaft per cylinder bank is driven by a fiberglass-reinforced toothed belt.
一个位于中央的每缸银行是由凸轮轴驱动的玻璃纤维增强型齿形带。
youdao
25. Using the so-called hall effect the hall sensors determine the position of the respective camshaft.
利用所谓的霍尔效应，霍尔效应传感器可确定各凸轮轴的位置。
youdao
26. The timing is controlled by the camshaft which is synchronized to the crankshaft by a chain or belt.
凸轮轴通过皮带链接与机轴保持同步，准确控制了可燃气体的进出时间。
youdao
27. The front of the cylinder head is also equipped with oil galleries to supply the intake camshaft VVT.
气缸头的前部还装有油画廊供应量凸轮轴可变配气相位。
youdao
28. In the engine, oil is supplied to crankshaft and camshaft journals rotating in their supporting bearings.
在发动机里，机油被供应到旋转在其支承轴内的曲轴和凸轮轴轴颈上。
youdao
29. A system of automated NC camshaft grinding machine with moderate price and high capability was developed.
为此，开发了一套价格适中的高性能数控凸轮磨床控制系统。
youdao
30. A system of automated NC camshaft grinding machine with moderate price and high capability was developed.
为此，开发了一套价格适中的高性能数控凸轮磨床控制系统。
youdao
camshaft
